Cooler Master Novatouch TKL

Cooler Master Novatouch TKL
Switch	Topre, 45g uniform weighting, MX mount
Sense method	Capacitive
Protocol	USB
Keycaps	Laser-engraved ABS

The Cooler Master Novatouch TKL is a keyboard sold by Cooler Master that uses Topre switches. This keyboard is notable for having using Cherry MX mount, compatible with modern custom keycap sets. The keyboard was released in late 2014 ¹⁾; and discontinued sometime around 2016 as claimed by a Cooler Master employee on Reddit. ²⁾

This keyboard uses capacitive Topre switches with a Cherry MX compatible keycap mount.

The keyboard was sold in both 87 key ANSI and 88 key ISO variants. The case is of a wrap-around design, with a Micro-USB port on the back for plugging in a detachable cable. The keyboard has “CM STORM” branding on the back edge on the side opposite of the Micro-USB port. The keyboard is capable of N-Key rollover on Windows ³⁾, but defaults to 6-key rollover on other operating systems.

The top case is of a wrap-around design. The top case has hidden clips along the top and bottom edges of the bottom case, then further secured using four black pan-head screws that screw up from the bottom case into screw sockets in the top case. The bottom case has four holes for these screws - two of them are exposed, whilst the other two are covered by the rear label and a warranty sticker - therefore requiring puncturing or peeling off said stickers to disassemble the keyboard.. There are four anti-slip rubber pads on the case, along with two flip-out feet that adjust the typing angle. The flip out feet has two additional anti-slip rubber pads to prevent slipping when the feet are extended out.

The keyboard assembly sits within the bottom case. The bottom case has pegs which help in aligning the keyboard assembly, with subsequent holes in the PCB to accommodate for the pegs. The Micro-USB port has two clips and two silver flat-head screws securing it to the bottom case, and is plugged into a 5-pin JST socket on the keyboard assembly; whilst the keyboard assembly is secured to the bottom case with two black pan-head screws.

The keyboard assembly consists of individual sliders and housings clipped into a steel metal plate, sitting over a rubber dome mat that covers capacitive cone-shaped springs that interact with the PCB to increase or decrease capacitance; this assembly is assembled using two different types of screws - 12 silver screws along the edge of the PCB with their location indicated by silk-screened circles, and 20 black screws throughout the PCB with locations indicated by arrows. The rubber dome mat sticks to the PCB from the factory; this seal may weaken overtime if the user frequently disassembles the assembly. The PCB also has two JST sockets - one slim one near the edge of the PCB that is left unused for normal usage, and a 5-pin JST socket where the Micro-USB port connects to the keyboard assembly.

The keyboard assembly has three or four stabilized housings for the Backspace, Enter, and Shift keys depending on ISO or ANSI layout; and 1 unit housings for all the other keys, including the spacebar - an external coil spring is placed over the spacebar's switch to make the spacebar slightly stiffer than other keys. Futhermore, the spacebar has two stabilizer housings that contain their corresponding sliders.

The spacebar is 6.25 units long and compatible with MX spacebars with a stem in the centre; the spacebar interfaces with three sliders - the 1 unit switch slider, and two stabilizer sliders on either end of the spacebar; the stabilizer sliders are hooked into a wire, with the wire clipping into corresponding hooks inside of the the stabilizer housing.

The housings for other stabilized keys have three holes - one that interfaces with the centre keycap stem, and two that allows the other keycap stems to freely move through. The holes on the left and right of the housing have “crowns” that protrude upward. The slider has two semi-circle nubs that poke through the left and right holes of the housing.

Disassembly of the keyboard assembly is required to access the wires for stabilized keys and the spacebar stabilizer.

The stock keycaps are ABS with lasered and infilled legends, with Cherry MX mount. Legends vary by localized variants.